Valcom V-9908 Especificaciones

Busca en linea o descarga Especificaciones para Sistemas de intercomunicación de la puerta Valcom V-9908. Valcom V-9908 door intercom system Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 6
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
9479801
Issue 1
V-9908 MESSAGE/PAGE PANEL
Introduction
These instructions contain the specifications and
guidelines necessary to install, operate, and
maintain the V-9908, Message/Page Panel.
The V-9908 Message/Page Panel is used with
Valcom Supervised Distributed Amplified One-Way
Paging Speakers and Horns providing full system
supervision.
The V-9908 provides a handheld push-to-talk
microphone for live pages and storage for eight
messages. The unit provides full system supervision
including the microphone and speaker line.
Applications
Valcom Supervised Distributed Amplified
One-Way Paging Systems.
Refer to Figure 1 for a block diagram of a typical
installation.
Features
Dynamic noise canceling handheld microphone
for live page
Provides up to 8 minutes of high quality digital
recording
Stores and plays up to 8 messages
PC Programmable
Message panel fully supervised
Provides speaker line supervision
Provides microphone supervision
Provides DC power supervision
Allows remote message activation
Visual and audible system trouble indication
Audible signal cancel button
Power "ON" indicator
Mounts in most 4 gang deep electrical box
Dimensions
5"W x 4.25"H x 2”D
(12.7cm W x 10.8cm D x 5.08cm H)
4 lbs. (1.5Kg)
Specifications
Power Requirements
Operating Voltage 22 – 26VDC
Current 100mA
Microphone Input
Input Impedance: >5000 Ohms
Input sensitivity: 1kHz 1 millivolt for -12dBm
output (output terminated with 100 Ohms)
Audio
Frequency Response:
Mic – Output: 150Hz – 7,000Hz
Frequency Response:
Stored Messages – Output: 150Hz – 3,500Hz
Input Sensitivity (mic): 1kHz 1 millivolt for -12dBm
output (output terminated with 100 Ohms)
Signal to Noise (Idle mode, Ref -12dBm): >70dB
Signal to Noise (Mic active, Ref -12dBm) >50dB
Distortion (Mic – Output): < 1% THD at -12dBm
Output Impedance: < 25 Ohms
Nominal output level: -12dBm (Ref 600 Ohms)
Maximum output level: 0dBm (before clipping)
System Supervision
Main Audio Channel: 30Hz tone (inaudible)
Microphone: 1kHz tone supervises the preamp,
cable and element
Microphone Switch: DC loop with 4.7K Ohm resistor
Audio Output: DC loop terminated with a 4.7K Ohm
1/4W resistor
Voice Storage Memory: Fixed segment memory
monitoring
Main Power: 9VDC battery provides redundant
supervision power
Battery: Low voltage monitoring
All system faults are indicated by both an audible
and visual alarm. The audible
alarm may be
silenced, however, the visual indicator will continue
to illuminate until the fault is removed.
Vista de pagina 0
1 2 3 4 5 6

Indice de contenidos

Pagina 1 - V-9908 MESSAGE/PAGE PANEL

9479801Issue 1V-9908 MESSAGE/PAGE PANELIntroductionThese instructions contain the specifications andguidelines necessary to install, operate, andmaint

Pagina 2 - Installation

9479802User Controls (Figure 1)• Push-to-Talk Microphone• Pushbuttons to activate pre-recorded messages• Pushbutton to cancel message play• Pushbut

Pagina 3 - TECHNICAL ASSISTANCE

9479803Using an RJ-45 connector, connect speaker audio(Tip and Ring) and speaker power to boardmounted connector as shown on connectingdiagram.All con

Pagina 4 - Figure 2: Rear Connections

9479804Figure 1: User Control LocationsEight (8) MessagePlay IndicatorsEight (8) MessagePlay ButtonsMessage LabelWindowSystem FaultIndicatorFault Aud

Pagina 5 - Figure 3: Typical Connections

9479805Audio InterfaceMessagePanel TipOutMessagePanel RingOutMessagePanel PlayContactV-2924A Page PortOverride InputAudioOutputAudioInputMessage Panel

Pagina 6

9479806Audio InterfaceAudioInputAudioOutputTo Unsupervised ValcomAmplified SpeakersN.C.N.C.MessagePanel TipOutMessagePanel RingOutMessagePanel PlayCon

Comentarios a estos manuales

Sin comentarios